Large aile fusées éclairantes passages de roue pour MITSUBISHI PAJERO (MONTERO) 2 PORTES MK2 vente en gros
This set of arches (4 pieces) are made for the MITSUBISHI PAJERO (MONTERO) 2-DOOR, year 1991 – 1998, second generation (MK2).They stick out around 8 cm, so they will cover well if you have oversize tires. They are only good for the model that comes without flares and side fairings. If your car has the original flares and side fairings you cannot install these. They will not cover the holes that will be left on the sides when you remove the original plastic arches and fairings. Also, the model with the side fairings has different bumpers that are not compatible with these flares.

These flares were developed on the canvas model, which doesnt have the small rounded indicators on the front sides. If you have the saloon model, the flares will cover a small part of the indicators. You will need to trim the flare a bit where it fits over the indicator, which will still be visible on its most part.

They are made of good quality, hand-laid fiberglass and the surface is black gelcoat, mat textured. Make sure your car is the model described above and shown in the photos. If you are in doubt, send me a few photos of your car showing the front, sides and back. I will reply within a day and let you know if it’s the right model.
The pocket style flares were originally designed to be fitted by drilling and screwing through the flare pockets and into the side of the vehicle. But since most car owners are reluctant to drill holes on the sides of their cars, we have developed another way for installation.
Each arch can be installed by drilling and screwing self tapping screws through the underside flange and sheet metal strips which are fixed on the fiberglass. The flanges of the flares touch the car wings flanges only at the ends while at the top they remain about 2 cm lower than the car wing flanges and are fixed there by sheet metal strips. To install, removing the adjacent wheel is recommended, so that you have enough space to use the drill. The help of another person is needed to hold the flare in place while the installer drills and screws.

The front flares are designed so that they fit clear of the lower edge of the car wing. This was done to make sure the over-wide tires do not rub on the rear end of the flares (look at the photos).
The arches are best installed by a professional or an experienced amateur. This is a difficult to install item. Don’t try this yourself if you don’t have enough experience.
We include the necessary screws, washers and rubber trim.
We ship from Cyprus (member of European Union). Parcels are sent by first priority airmail.

Every fiberglass product is made especially for you, after your order. The procedure takes a maximum of 20 business days. Usually, we are ready to ship within 18 to 19 working days. When the items are ready we package and ship them and email the tracking number to you, along with fitting instructions and a series of photos that will help your installer do a perfect installation job.

Note: Buyers from all EU countries will not pay any tax when they receive the item.
Theres usually a tax involved for all other countries, which is paid by the recipients when they receive the item.
If you reside in USA, you must know that most States require that eBay collects the sales tax at the time an item is bought from eBay, and then remits it to the proper State authorities.


This set of arches (4 pieces) are made for the MITSUBISHI PAJERO (MONTERO) 2-DOOR, year 1991 – 1998, second generation (MK2).They stick out around 8 cm, so they will cover well if you have oversize tires. They are only good for the model that comes without flares and side fairings. If your car has the original flares and side fairings you cannot install these. They will not cover the holes that will be left on the sides when you remove the original plastic arches and fairings. Also, the model with the side fairings has different bumpers that are not compatible with these flares.

These flares were developed on the canvas model, which doesnt have the small rounded indicators on the front sides. If you have the saloon model, the flares will cover a small part of the indicators. You will need to trim the flare a bit where it fits over the indicator, which will still be visible on its most part.

They are made of good quality, hand-laid fiberglass and the surface is black gelcoat, mat textured. Make sure your car is the model described above and shown in the photos. If you are in doubt, send me a few photos of your car showing the front, sides and back. I will reply within a day and let you know if it’s the right model.
The pocket style flares were originally designed to be fitted by drilling and screwing through the flare pockets and into the side of the vehicle. But since most car owners are reluctant to drill holes on the sides of their cars, we have developed another way for installation.
Each arch can be installed by drilling and screwing self tapping screws through the underside flange and sheet metal strips which are fixed on the fiberglass. The flanges of the flares touch the car wings flanges only at the ends while at the top they remain about 2 cm lower than the car wing flanges and are fixed there by sheet metal strips. To install, removing the adjacent wheel is recommended, so that you have enough space to use the drill. The help of another person is needed to hold the flare in place while the installer drills and screws.

The front flares are designed so that they fit clear of the lower edge of the car wing. This was done to make sure the over-wide tires do not rub on the rear end of the flares (look at the photos).
The arches are best installed by a professional or an experienced amateur. This is a difficult to install item. Don’t try this yourself if you don’t have enough experience.
We include the necessary screws, washers and rubber trim.
We ship from Cyprus (member of European Union). Parcels are sent by first priority airmail.

Every fiberglass product is made especially for you, after your order. The procedure takes a maximum of 20 business days. Usually, we are ready to ship within 18 to 19 working days. When the items are ready we package and ship them and email the tracking number to you, along with fitting instructions and a series of photos that will help your installer do a perfect installation job.

Note: Buyers from all EU countries will not pay any tax when they receive the item.
Theres usually a tax involved for all other countries, which is paid by the recipients when they receive the item.
If you reside in USA, you must know that most States require that eBay collects the sales tax at the time an item is bought from eBay, and then remits it to the proper State authorities.


Large aile fusées éclairantes passages de roue pour MITSUBISHI PAJERO (MONTERO) 2 PORTES MK2 vente en gros

Large aile fusées éclairantes passages de roue pour MITSUBISHI PAJERO (MONTERO) 2 PORTES MK2 vente en gros, Large aile fusées éclairantes passages de roue pour MITSUBISHI PAJERO (MONTERO) 2 PORTES MK2 liquidation

€438.01

SKU: 794065

Colour
Size guide
Out of stock
Personalised:
: ( x )
Personalisation:
Edit
Remove Personalisation
Frasers Plus

Buy now.

Pay later.

Earn rewards

Representative APR: 29.9% (variable)

Credit subject to status. Terms apply.

Missed payments may affect your credit score

FrasersPlus